Hp6050a Driver

HP Deskjet 3050A Driver Downloads for Microsoft Windows and Macintosh Operating System.

Keysight Technologies / Agilent Technologies hp605xa Electronic Load Multi-Environment Plug and Play Instrument Driver.

hp6050a driver

Download the latest software and drivers for your HP Deskjet 3050A e-All-in-One Printer - J611g.

Hp6050a driver. Hp6050a driver to do hp6050a driver xbox 360 Hp6050a driver driver That hp6050a driver hp6050a cabbie 64-bit expression. hp6050a driver.

Hi Edilberto. That VI configures input and output subsystems.

State: Turns the electronic load input ON or OFF.When input is OFF, the electronic load will draw minimal current at its input.The state of INPUT OFF overrides the state of SHORT ON.The presently programmed slew rate setting is not used when turning the input on or off; the current and voltage change at their maximum rates.

Short: This control applies the equivalent of an electronic short across the input of the electronic load.The actual condition of the electronic load under a short condition depends on its operating mode.For details, refer to Chapter 4 of the programming manual.

Protection Clear: Resets the electronic load latched protective features such as over voltage, over current, overpower, etc..

If a trigger is received during the time a protection circuit has shut down the input, any triggered levels are stored and will be transferred to the main level after the protection is cleared.Triggers received during protective shutdown are also applied to the Transient subsystem.

Output: Controls the general-purpose digital port on the rear of each electronic load or each channel of the multiple electronic load.The state of the port is with respect to the common side of the electronic load input.Setting a port to ON state disconnects it from common and sets its to a TTL logical high.

For additional information start the context help CTRL H and you can see each part in the LabVIEW version of the driver

By the way there are forums in Spanish available now

Senior Systems Engineer // CLA // CLED // CTD

I have troubles with my boss. I need to trap the modem ring while it is working tranferring data. How can I use DDK or existent filter to obtain that.

The M-Series User Manual, Chapter 6, Digital I/O,  talks about Programmable Power-up States and sending TTL level outputs.  What functions in the DDK are used to configure these settings.  Is there any sample code.

The spec sheets for the 6225 and 6259 describe Output High Current and Output Low Current.  Is there anything to configure here or are these intended to be operating limits.

I have been doing some performance measurements on the code needed for a writing samples to the DA FIFO and b reading data from the AD FIFO on a 6259 board using the DDK samples and the VISA package.

The code in case a is just a loop including sample conversion and register write. I case b it is a check empty flag - read register - convert sample loop. In my application I need 16 input channels at 40 kS/s and 4 output channels at 40 kS/s. The data will be processed in chunks of 40 samples/channel every 1 ms.

a Writing 20 samples to the DA FIFO takes 3.2 us 0.16 us/sample

b Reading 100 samples from the AD FIFO including check of FIFO empty flag takes 320 us 3.2 us/sample.

The results indicates that a register read takes  approx. 10 times longer than a register write. Since I will be reading 640 samples and writing 160 samples every 1 ms in my application, this isn t fast enough.

Is the read access to the board registers really this slow compared to writes or is there some wait-state settings that need some tweeking.

Whould I gain any performance using DMA.

The tests are performed on a Intel Xeon 3.8GHz machine.

I have the HP OfficeJet 6500A Plus E710n-z series for All-In-One Printer. I lost my driver software disk together with the PC computer that had the software driver.

Hi. Could someone explain me what is the function of the config.input_output vi of the HP6050a instrument driver. I mean, what is it for. How do I use its inputs and.